3.9 KiB
3.9 KiB
| 1 | Category | Qty | Description | Manufacturer Part Number | Link | Notes |
|---|---|---|---|---|---|---|
| 2 | Electronics | 1 | ZimaBoard 832 Single Board Server | https://geni.us/uwBCZ | Main SBC — the brain of the NAS | |
| 3 | Electronics | 2 | Noctua NF-A4x10 FLX 3-Pin 12V (40x10mm) | NF-A4x10 FLX | https://geni.us/Fkr3L | Drive bay intake fans — small form factor for tight spacing |
| 4 | Electronics | 2 | Noctua NF-R8 redux-1800 3-Pin 12V (80mm) | NF-R8 redux-1800 | https://geni.us/5GhNKWv | Rear exhaust fans — main case cooling |
| 5 | Electronics | 1 | Momentary Push Button 12V LED Ring (16mm hole) | https://geni.us/luLH | Power button — 16mm matches the face plate cutout | |
| 6 | Electronics | 1 | SATA PCIe Expansion Card (4 Ports) | https://geni.us/9vRfBY | Adds 4 SATA ports to ZimaBoard's native 2 for 6 total | |
| 7 | Electronics | 1 | 90 Degree PCI Extension Cable (15cm) | https://geni.us/D940HF5 | PCIe riser — needed because ZimaBoard is mounted perpendicular to SATA card | |
| 8 | Electronics | 2 | Molex IDE Male to 3x 15-Pin SATA Power Splitter | https://geni.us/eeVQD | Splits PCB drive power into per-drive SATA power connectors | |
| 9 | Electronics | 1 | Power Socket Inlet Module | https://geni.us/WkVR7 | IEC C14 panel mount — standard PC power cable socket | |
| 10 | Electronics | 6 | SATA 22-Pin (7+15) Male to Female Extender | https://geni.us/wC48Yf | Pass-through cables from drive bays to rear — avoids bending cables at sharp angles | |
| 11 | Electronics | 1 | Multiple Output PSU 5V(10A) 12V(12A) | N/A | Dual-rail power supply — must provide both 5V and 12V simultaneously | |
| 12 | PCB | 1 | Terminal Block 3-pos 5.08mm TH | 691216510003S | Digikey: 732-691216510003S-ND | PSU_IN connector — 5V / 12V / GND input from power supply |
| 13 | PCB | 1 | Header TH 4-pos 2.54mm | 61300411021 | Digikey: 732-5337-ND | POWER_SW connector — momentary button interface |
| 14 | PCB | 1 | Header TH 6-pos 2.54mm | 61300621121 | Digikey: 732-5295-ND | ZIMA_PWR connector — delivers regulated power to ZimaBoard |
| 15 | PCB | 1 | Header TH 14-pos 2.54mm | 61301421121 | Digikey: 732-5298-ND | ZIMA_IO connector — IO passthrough to ZimaBoard |
| 16 | PCB | 4 | Ceramic Capacitor 0.1uF 50V X7R 1206 | C1206C104K5RACTU | Digikey: 399-C1206C104K5RACTUCT-ND | Decoupling caps — one per MOSFET/transistor pair for switching noise suppression |
| 17 | PCB | 4 | Resistor 10k 1% 0.25W 1206 | Digikey: 311-10.0KFRCT-ND | Gate pullup/bias resistors — set MOSFET default state and BJT base bias | |
| 18 | PCB | 4 | Electrolytic Capacitor 10uF 50V | WCAP-ASLI 4x5.5 | Digikey: 732-8451-1-ND | Bulk filtering — smooth voltage ripple on 5V and 12V rails |
| 19 | PCB | 2 | PTC Resettable Fuse 16V 10A TH | Digikey: PTR016V1000-BK-ND | Overcurrent protection — self-resets after fault clears (one per rail) | |
| 20 | PCB | 4 | Molex Header TH 3-pos 2.54mm | 22-23-2031 | Digikey: WM4201-ND | Fan headers X1-X4 — standard 3-pin fan connector pinout |
| 21 | PCB | 2 | Molex Header TH 4-pos 5.08mm | 350211-1 | Digikey: A1212-ND | DRIVES_PWR1/PWR2 — Molex power to drive SATA splitters |
| 22 | PCB | 2 | P-Channel MOSFET 30V 40A TO-252 | G40P03K | Digikey: 3141-G40P03KCT-ND | High-side power switching — one per rail (5V and 12V) |
| 23 | PCB | 2 | NPN Transistor 40V 600mA SOT-23 | MMBT2222AL | Digikey: MMBT2222ALT1GOSCT-ND | Gate drive — level shifts logic signal to MOSFET gate voltage |
| 24 | PCB | 1 | Receptacle 6-pos 2.54mm | Digikey: 732-61300621821-ND | ZIMA_PWR mating connector — plugs into the 6-pin header | |
| 25 | PCB | 1 | Receptacle 14-pos 2.54mm | Digikey: 2057-RS2-14-G-ND | ZIMA_IO mating connector — plugs into the 14-pin header | |
| 26 | Hardware | 52 | M3 x 10-12mm Hex Socket Countersunk Head Screw | https://geni.us/bYhU | Frame and cover assembly — countersunk for flush fit | |
| 27 | Hardware | 20 | M3 x 10mm Hex Socket Head Cap Screw | https://geni.us/5N61va | Component mounting — cap head where flush fit not needed | |
| 28 | Hardware | 72 | M3 Heat-Set Inserts | https://geni.us/PdB8mWk | Press into printed parts with soldering iron — creates reusable threaded holes | |
| 29 | Hardware | 6 | M6 Fully Threaded Rod | https://geni.us/T6Quy | Drive bay rails — drives slide along these rods | |
| 30 | Hardware | 12 | M6 Hex Nut | https://geni.us/BPGwNiY | Rod fastening — 2 per rod (top and bottom) | |
| 31 | Hardware | 29 | M6 Nylon Washer (1.2mm thickness) | https://geni.us/38l20a | Drive bay spacing — sits between drive slots to set correct bay gap |