32 lines
3.9 KiB
Plaintext
32 lines
3.9 KiB
Plaintext
Category,Qty,Description,Manufacturer Part Number,Link,Notes
|
|
Electronics,1,ZimaBoard 832 Single Board Server,,https://geni.us/uwBCZ,Main SBC — the brain of the NAS
|
|
Electronics,2,Noctua NF-A4x10 FLX 3-Pin 12V (40x10mm),NF-A4x10 FLX,https://geni.us/Fkr3L,Drive bay intake fans — small form factor for tight spacing
|
|
Electronics,2,Noctua NF-R8 redux-1800 3-Pin 12V (80mm),NF-R8 redux-1800,https://geni.us/5GhNKWv,Rear exhaust fans — main case cooling
|
|
Electronics,1,Momentary Push Button 12V LED Ring (16mm hole),,https://geni.us/luLH,Power button — 16mm matches the face plate cutout
|
|
Electronics,1,SATA PCIe Expansion Card (4 Ports),,https://geni.us/9vRfBY,Adds 4 SATA ports to ZimaBoard's native 2 for 6 total
|
|
Electronics,1,90 Degree PCI Extension Cable (15cm),,https://geni.us/D940HF5,PCIe riser — needed because ZimaBoard is mounted perpendicular to SATA card
|
|
Electronics,2,Molex IDE Male to 3x 15-Pin SATA Power Splitter,,https://geni.us/eeVQD,Splits PCB drive power into per-drive SATA power connectors
|
|
Electronics,1,Power Socket Inlet Module,,https://geni.us/WkVR7,IEC C14 panel mount — standard PC power cable socket
|
|
Electronics,6,SATA 22-Pin (7+15) Male to Female Extender,,https://geni.us/wC48Yf,Pass-through cables from drive bays to rear — avoids bending cables at sharp angles
|
|
Electronics,1,Multiple Output PSU 5V(10A) 12V(12A),,N/A,Dual-rail power supply — must provide both 5V and 12V simultaneously
|
|
PCB,1,"Terminal Block 3-pos 5.08mm TH",691216510003S,Digikey: 732-691216510003S-ND,PSU_IN connector — 5V / 12V / GND input from power supply
|
|
PCB,1,"Header TH 4-pos 2.54mm",61300411021,Digikey: 732-5337-ND,POWER_SW connector — momentary button interface
|
|
PCB,1,"Header TH 6-pos 2.54mm",61300621121,Digikey: 732-5295-ND,ZIMA_PWR connector — delivers regulated power to ZimaBoard
|
|
PCB,1,"Header TH 14-pos 2.54mm",61301421121,Digikey: 732-5298-ND,ZIMA_IO connector — IO passthrough to ZimaBoard
|
|
PCB,4,"Ceramic Capacitor 0.1uF 50V X7R 1206",C1206C104K5RACTU,Digikey: 399-C1206C104K5RACTUCT-ND,Decoupling caps — one per MOSFET/transistor pair for switching noise suppression
|
|
PCB,4,"Resistor 10k 1% 0.25W 1206",,Digikey: 311-10.0KFRCT-ND,Gate pullup/bias resistors — set MOSFET default state and BJT base bias
|
|
PCB,4,"Electrolytic Capacitor 10uF 50V",WCAP-ASLI 4x5.5,Digikey: 732-8451-1-ND,Bulk filtering — smooth voltage ripple on 5V and 12V rails
|
|
PCB,2,"PTC Resettable Fuse 16V 10A TH",,Digikey: PTR016V1000-BK-ND,Overcurrent protection — self-resets after fault clears (one per rail)
|
|
PCB,4,"Molex Header TH 3-pos 2.54mm",22-23-2031,Digikey: WM4201-ND,Fan headers X1-X4 — standard 3-pin fan connector pinout
|
|
PCB,2,"Molex Header TH 4-pos 5.08mm",350211-1,Digikey: A1212-ND,DRIVES_PWR1/PWR2 — Molex power to drive SATA splitters
|
|
PCB,2,"P-Channel MOSFET 30V 40A TO-252",G40P03K,Digikey: 3141-G40P03KCT-ND,High-side power switching — one per rail (5V and 12V)
|
|
PCB,2,"NPN Transistor 40V 600mA SOT-23",MMBT2222AL,Digikey: MMBT2222ALT1GOSCT-ND,Gate drive — level shifts logic signal to MOSFET gate voltage
|
|
PCB,1,"Receptacle 6-pos 2.54mm",,Digikey: 732-61300621821-ND,ZIMA_PWR mating connector — plugs into the 6-pin header
|
|
PCB,1,"Receptacle 14-pos 2.54mm",,Digikey: 2057-RS2-14-G-ND,ZIMA_IO mating connector — plugs into the 14-pin header
|
|
Hardware,52,M3 x 10-12mm Hex Socket Countersunk Head Screw,,https://geni.us/bYhU,Frame and cover assembly — countersunk for flush fit
|
|
Hardware,20,M3 x 10mm Hex Socket Head Cap Screw,,https://geni.us/5N61va,Component mounting — cap head where flush fit not needed
|
|
Hardware,72,M3 Heat-Set Inserts,,https://geni.us/PdB8mWk,Press into printed parts with soldering iron — creates reusable threaded holes
|
|
Hardware,6,M6 Fully Threaded Rod,,https://geni.us/T6Quy,Drive bay rails — drives slide along these rods
|
|
Hardware,12,M6 Hex Nut,,https://geni.us/BPGwNiY,Rod fastening — 2 per rod (top and bottom)
|
|
Hardware,29,M6 Nylon Washer (1.2mm thickness),,https://geni.us/38l20a,Drive bay spacing — sits between drive slots to set correct bay gap
|