Several issues addressed in this PR:
- CutFilament tuning + error recovery
- introduce register 0x1d (cut filament selector iRun current level)
- optimize setting iRun and iHold currents in the FW
- CutFilament unit test fixed
Intended for scenarios when FINDA used to be OFF but accidentally became ON without a reason.
The user is obliged to inspect FINDA and tune its switching.
This is to solve a potential problem while feeding to printer's drive gears - while disengaging the Idler, the Pulley was still rotating to avoid grinding the filament (printer is pulling it).
Other filaments could have moved a bit when the Idler's bearings ran over them while the Pulley was still rotating slowly -> the filament could have been moved into the Selector's path causing trouble (especially when not used in the print).
Therefore, the Idler disengages partially now - moves into an intermediate position between the slots.
Then, the Pulley is completely stopped and after that the Idler does a full disengage like before.
If the MMU receives a command LoadFilament with a slot number SL we reject
the command to avoid moving the selector (effectively cutting the piece of filament present in FINDA).
That includes the scenario when the selector is standing at the very same slot SL, because the filament could be held by the printer (i.e. loaded in the nozzle).
There is one special case though - same slot AND filament load state == InSelector (it MUST NOT be anywhere farther)
This commit looks horribly complex, but the main idea is to have each of the logic::commands
report their terminal OK state in the same way. That allow for leveraging this very moment
to initiate the idle timeout.
Additionally, I wanted to hide the logic of idle mode detection, which resulted in moving the
top level logic from main.cpp into logic/idle_mode.cpp and a set of additional files to compile
in unit tests.
- circular buffer can return its count of elements (even though a better solution may be implemeted later)
- stub_motion can handle multiple planned moves
- improved load/unload filament tests
This PR brings the option to move the selector directly using
buttons of the MMU - obviously while the MMU is idle and no
filament is stuck in the selector.
Left/Right buttons move the selector Left/Right.
Middle button performs a LoadFilament (into the MMU) on the active slot.
With this PR a change of LoadFilament behavior is also introduced.
Now, LoadFilament spins the Pulley for infinite time while waiting
for either FINDA trigger and/or a button pressed.
This PR brings the following improvements:
- unifies the error handling of TMC and Homing/Stallguard errors on all motorized modules (Idler, Selector, Pulley)
- now we distinguish between Homing and TMC errors + we have a separate handling of these two kinds into CommandBase unified for all motorized modules
- adds unit tests to verify the function
- fixes SetFINDAStateAndDebounce (didn't obey the press parameter before)
Solves an interesting tiny issue introduced in the previous commits.
When we start with the filament in selector, the corresponding LED
is set to ON. However, all of the logic state machines only operated
on the LED pair of the active slot -> the starting LED may have been
left ON in some edge cases.
Now, this is resolved by clearing all other LEDs except for the active
slot where appropriate.
Both movable components now perform homing sequences transparently
whenever the logic layer invalidates the homingValid flag.
That reflects the fact, that the user may have moved the Idler or Selector
while trying to resolve a HW issue with un/loading filament.
Basic rules:
- Idler gets rehomed immediately and then moves into the target slot position
- Selector rehomes once it is possible - i.e. when filament load state
is AtPulley - then it immediately and spontanneously executes the homing
sequence and then returns to the desired state
Motivation:
- resolve startup issues (EEPROM says we have filament, but FINDA is not triggered)
- resolve accidental moves of Idler and/or Selector while
digging out stuck filament from the unit
That includes:
- introduce pulley slow feedrate and fsensor-to-nozzle distance
in config necessary for slowly feeding the filament from fsensor into the nozzle.
(the constant is subject to extraction into some other config as it has to be used in the printer as well).
- update FeedToBondtech accordingly to perform a gentle push into the nozzle
after fsensor detects the filament + update its unit tests.
- slight cleanup of LoadFilament + fix its unit tests
- add FeedingToNozzle progress code, as it might be interesting
to inform the printer about this task in the future
- revert non-clean changes from RetractFromFinda - it should not disengage the idler
- revert incorrect + fix ToolChange
- clean-up UnloadFilament
- feed to finda engages the idler so no need to do that before
- retract from finda disengages the idler, again avoid double operation
LEDs set mostly by feed to finda and retract from finda
because of the change of semantics of LoadFilament operation.
LoadFilament pushes the filament into FINDA and then retracts it back just to keep the
filament ready to be grabbed by the idler and pulley and loaded into the printer's nozzle.
So the selector is not blocked by the filament -> filament NOT loaded
Load filament performs feed to FINDA and retract:
- engage idler
- feed normal to FINDA with config::feedToFinda distance until FINDA triggers
- retract normal and as soon FINDA un-triggers move back to PTFE config::cuttingEdgeToFindaMidpoint
- disengage the idler
That implied introducing another substate machine - RetractFromFinda, which does the opposite
of FeedToFinda while also checking for the FINDA switching off while retracting filament.
Still, ToolChange and CutFilament need fixing with this change
Besides Unload Filament, which only operates on active slot, all other
top level state machines check the validity of the command's parameter.
If the parameter is out of range for available slots, they return
ErrorCode::INVALID_TOOL now.
- Distinguish among FINDA on/off failuje
- The same applies to newly introduced Filament sensor errors
- Add TMC init error
- Add a communication error ID - to be used on the printer
Implement Motion::SetEnabled (for symmetry with TMC2130::SetEnabled).
Rename DisableAxis to Disable and use the new SetEnabled. This makes the
member names more consistent.
D.R.racer
3d-gussner
Yuri D'Elia