- rename stall*guard to StallGuard (match name with the vendor)
- separate TMC2130 module from EEPROM (they do not need to know about each other at all)
- separate SGTHRS settings from motion - moved to globals like all other "global" parameters
- improved EEPROM storage for SGTHRS
This is to solve a potential problem while feeding to printer's drive gears - while disengaging the Idler, the Pulley was still rotating to avoid grinding the filament (printer is pulling it).
Other filaments could have moved a bit when the Idler's bearings ran over them while the Pulley was still rotating slowly -> the filament could have been moved into the Selector's path causing trouble (especially when not used in the print).
Therefore, the Idler disengages partially now - moves into an intermediate position between the slots.
Then, the Pulley is completely stopped and after that the Idler does a full disengage like before.
It looks we have some kind of leak when filament sensor state is not completely coherent with FINDA state.
This is yet to be discovered and fixed with some unit tests.
If the MMU receives a command LoadFilament with a slot number SL we reject
the command to avoid moving the selector (effectively cutting the piece of filament present in FINDA).
That includes the scenario when the selector is standing at the very same slot SL, because the filament could be held by the printer (i.e. loaded in the nozzle).
There is one special case though - same slot AND filament load state == InSelector (it MUST NOT be anywhere farther)
It turned out FINDA needs running timer to perform BlockingInit() correctly.
Therefore setup() was split into setup() (no IRQ) and setup2() (IRQ enabled).
Then, finally, the check for FINDA state became reliable upon start of the FW.
Originally, only FeedingToBondtech was reported to the printer.
With PR#173 we have this operation separated into a fast and a slow stage (for MK3S with the chimney).
It looks like the printer could benefit from knowing if the MMU is still pushing fast
or when it entered the slow stage (to prevent ramming hard the Bondtech gears)
Along with this new state being reported, we also introduce a new ErrorCode::FSENSOR_TOO_EARLY
which basically means that the fsensor triggered in the fast feeding stage.
- Check rates using the reported acceleration instead of deriving the
value from the slope.
- Simplify the tolerances when checking (use 10% for single-axis,
20% with multiple due to quantization)
- Check a broader range of values
Correctly compute both the number of steps and direction when
under/overflowing the current position by performing a relative move.
This makes a repeated PlanMove() _always_ perform the move correcly,
even when the upper-level code might require to handle the overflow
itself for measurement.
Add tests for this condition by exposing the internal CurBlockShift() to
the motion unit tests.
Do not assume any step can be merged while moving three axes at the same
time.
Use the worst case scenario involving indepedent parameters for each
axis.
This commit looks horribly complex, but the main idea is to have each of the logic::commands
report their terminal OK state in the same way. That allow for leveraging this very moment
to initiate the idle timeout.
Additionally, I wanted to hide the logic of idle mode detection, which resulted in moving the
top level logic from main.cpp into logic/idle_mode.cpp and a set of additional files to compile
in unit tests.
- circular buffer can return its count of elements (even though a better solution may be implemeted later)
- stub_motion can handle multiple planned moves
- improved load/unload filament tests
While motion queuing is safe, code that relies on the current block
needs to run with the isr disabled.
Protect AbortPlannedMoves and CurPosition from isr' interference by
using a RAII guard.
The principle has been implemented, but the TMC is not providing
the right data for some reason - homing doesn't work at all right now.
Also, after solving the physical homing, unit tests must be updated.
D.R.racer
vintagepc
Yuri D'Elia